Four ways to define the slope of a river
A longitudinal profile plots bed or water-line elevation against distance along the channel. Most time-of-concentration formulas need one number for the slope, and real profiles are curved: steep in the headwaters, flat near the outlet. The four standard definitions summarise that curve differently.
Average slope, total fall over total length:
10-85 slope (Benson, 1962), the fall between 10 % and 85 % of the length from the outlet:
Equal-area slope, the line through the outlet that leaves equal areas of profile above and below it. Because the line starts at the outlet, it has a closed form:
Taylor-Schwarz slope (Taylor and Schwarz, 1952), the uniform slope with the same travel time as the real channel, found by splitting it into reaches:
| Symbol | Meaning | Unit |
|---|---|---|
| Length of the main watercourse, outlet to source | m | |
| , | Elevations of the source and the outlet | m |
| , | Elevations at 10 % and 85 % of , measured from the outlet | m |
| Profile elevation at distance upstream of the outlet | m | |
| Area between the profile and the horizontal through the outlet | m² | |
| , | Length and slope of reach | m, m/m |
Studio evaluates the Taylor-Schwarz sum on ten reaches of equal length rather than on every sample point. At DEM spacing each small bump would add slope on the way up and again on the way down, which inflates the result. Adverse reaches are floored at a small positive slope so the sum stays finite. The 10-85 and equal-area methods find the outlet as the lower end of the line, so a profile digitised from source to outlet gives the same answer as one digitised the other way.
Getting a profile into the tool
There are four ways in:
- Upload a file: GeoJSON, zipped Shapefile, KML or KMZ, GPX, DXF, CSV, TSV or Excel. The tool detects whether the file holds coordinates, elevations or chainage only.
- Paste distance and elevation pairs from a spreadsheet, HEC-RAS station table or survey sheet, one point per line.
- Pick the longest watercourse from a saved watershed delineation, so the length matches the catchment you delineated.
- Trace between two points you click. In the US the trace follows the USGS NHDPlus network through NLDI; elsewhere it uses the Esri downstream trace.
A line without elevations gets them from one of three places: the global terrain composite (about 30 m, sampled with bilinear interpolation in your browser), the Esri world elevation service, or a slope you enter by hand. The source is recorded with the calculation and printed in the report.
Worked example: a 6.4 km concave watercourse
This profile is an illustrative headwater stream, steep at the source and flattening towards the outlet. All slopes below came from running the Studio slope engine on these eleven points.
| Chainage from outlet (m) | Elevation (m) |
|---|---|
| 0 | 1 012.0 |
| 400 | 1 014.5 |
| 800 | 1 018.0 |
| 1 600 | 1 027.0 |
| 2 400 | 1 040.0 |
| 3 200 | 1 056.0 |
| 4 000 | 1 075.0 |
| 4 800 | 1 098.0 |
| 5 600 | 1 130.0 |
| 6 000 | 1 152.0 |
| 6 400 | 1 185.0 |
Average. m/m.
10-85. The 10 % point is 640 m upstream, interpolated at 1 016.6 m; the 85 % point is 5 440 m upstream at 1 123.6 m. m/m.
Equal-area. The trapezoidal area between the profile and the 1 012.0 m datum is 354 800 m². m/m.
Taylor-Schwarz. Ten reaches of 640 m have slopes rising from 0.0072 at the outlet to 0.0722 at the source. The sum of is 45 529, so m/m.
Feeding each slope into the SANRAL Drainage Manual defined-watercourse formula, with in km and in hours, through Studio’s time of concentration calculator:
| Slope definition | Slope (m/m) | (min) |
|---|---|---|
| Average | 0.0270 | 66.7 |
| 10-85 | 0.0223 | 71.9 |
| Taylor-Schwarz | 0.0198 | 75.3 |
| Equal-area | 0.0173 | 79.2 |
The average slope is 56 % steeper than the equal-area slope, and the choice moves by 12.5 minutes, about 19 %. A shorter means a shorter, more intense design storm in the Rational Method, so here the average slope would give the highest peak. The SANRAL Drainage Manual pairs this formula with the 10-85 slope, so 71.9 minutes is the value to carry forward here.
Which slope for which method
| Method or use | Slope to use |
|---|---|
| SANRAL Drainage Manual defined-watercourse | 10-85 |
| Kirpich, NRCS lag, FAA | 10-85 or equal-area |
| FHWA three-segment travel time | Local slope of each segment |
| Long compound profiles with strongly varying gradient | Taylor-Schwarz |
| A quick check of fall over length | Average |
Elevation sources and profile artefacts
| DEM | Resolution | Notes |
|---|---|---|
| MERIT-Hydro | about 90 m | Hydrologically conditioned; suits catchments above about 10 km² |
| Terrain composite | about 30 m | Composite of USGS 3DEP, SRTM and other public DEMs; not conditioned |
| Esri world elevation | 10–30 m | Multi-source mosaic; accuracy varies by region |
| Delta Hydro COP30 | 30 m | Hydrologically corrected Copernicus GLO-30; South Africa, arrives with a COP30 delineation |
| Local LiDAR | 1–5 m | Best for small urban catchments and flat ground where you have coverage |
DEM profiles are rarely clean. Pits show as notches where a single cell is too low; use a conditioned DEM or force elevations to fall downstream. Spikes come from radar layover or vegetation; delete them in the paste editor. Flat steps appear where the channel follows one contour for several cells; the 10-85 slope is largely insensitive to them. SRTM-based data reads the canopy top under dense riparian forest, which lifts the profile. The slopes do not depend on which way the line was digitised; Reverse profile only flips the chart.
Limitations
The tool characterises a profile; it does not survey one. A 30 m or 90 m DEM cannot see a 2 m drop over a weir or a culvert invert, and on flat ground the DEM’s vertical error can be as large as the fall you are measuring. Where the design is sensitive to slope, use surveyed or LiDAR elevations and paste them in. Heavy smoothing can erase real knickpoints at confluences and waterfalls, so compare a smoothed profile with the raw one before accepting it. Bed slope from a long section is also not the friction slope a backwater model needs; for water-surface profiles use the gradually varied flow calculator.
What the full Studio tool adds
Profiles save to a project and export as a Word or Excel report with the long-section chart, and the line and its sample points export as GeoJSON, KML or Shapefile. Use in Tc Calculator opens a time of concentration calculation with length and slope filled in and locked to the profile, and later edits to the profile flow through to the linked calculation. In South Africa, Design Flood Estimation reports the 10-85, equal-area and Taylor-Schwarz slopes of its own 30 m flowpath, so a profile built here is an independent check on it.
Common questions
What is the 10-85 slope method?
How do you calculate the equal-area slope?
When should I use the Taylor-Schwarz slope?
Which slope should I use for time of concentration?
Where do I get elevations if my river line has none?
run_watercourse_profile. The agent passes the inputs, the engine does the calculation, and the record is saved to your project for you to review.
References
- Benson, M.A. (1962) Factors influencing the occurrence of floods in a humid region of diverse terrain. U.S. Geological Survey Water-Supply Paper 1580-B.
- Taylor, A.B. and Schwarz, H.E. (1952) Unit-hydrograph lag and peak flow related to basin characteristics. Transactions, American Geophysical Union, 33(2), 235-246.
- SANRAL (2013) Drainage Manual, 6th ed. South African National Roads Agency SOC Ltd, Pretoria. Chapter 3: Hydrology.
- Chow, V.T. (1959) Open-Channel Hydraulics. McGraw-Hill, New York.
- Yamazaki, D., Ikeshima, D., Sosa, J., Bates, P.D., Allen, G.H. and Pavelsky, T.M. (2019) MERIT Hydro: a high-resolution global hydrography map based on latest topography datasets. Water Resources Research, 55(6), 5053-5073.
Last reviewed by the Delta Hydro engineering team.